PHE0.1B Plate Heat Exchanger Auxiliary Brewing Equipments 3-10m²
Heat Exchange Area
The plate heat exchanger consists of a frame, which consists of a
head, follower, column, carrying bar, guiding bar, and a number of
clamping bolts. In between head and follower a varying number of
pressed plates are clamped together. Each plate is supplied with a gasket, so that the plates form a
closed system of parallel flow channels, through which the medias
flow alternatively at every second interval.
The Plate Stack - Media
The gaskets are glued on the plates, securing tightness between
medias and the atmosphere. Between the different medias there are
double gaskets, which have intermediate drain areas, meaning that
mixing of the two medias is impossible. Every second plate in the
stack has to turn 180°, so that the plates form a closed system of
parallel flow channels, through which the medias flow alternatively
at every second interval.
Gasket Construction
New Gaskets
The first plate after the head and intermediate frames is mounted
with a gasket in all the gasket grooves.These gaskets are cut out
of ordinary gaskets.
Glue Less or Glued Gaskets
Some plate heat exchangers are delivered with glue less "Sonder
Snap" gaskets. In these units it is possible to change the gaskets
without using glue. However, the gasket on the first plate after
the head and intermediate frame should be glued on in the pattern
displayed above.
Advantages
The plates and plate patterns are constructed to obtain a high
thermal efficiency with a low pressure drop
There are two pattern designs available with different pressing
angles giving respectively high/low turbulence flow, dependant on
the given selection
The inlet channels allow for maximum strength in the inlet area,
whilst maintaining minimum of contact points, reducing blockage at
the flow distribution zone
The inlet design ensures even distribution of the liquids across
the heating surface
The gasket is placed in a dedicated retaining gasket groove. This
secures the elasticity of the gasket even after a long time of
compression
The plate heat exchangers can be widely used for heating,
petroleum, chemical, food, paper, pharmaceuticals, machinery,
metallurgy and other different areas.
Technical Parameters
| Type | 0.05 | 0.1A | 0.1B | 0.2 | 0.23 | 0.3 | 0.55 | 0.85 | 1.0 |
| heat exchange area(m²) | 0.0618 | 0.0966 | 0.101 | 0.204 | 0.222 | 0.318 | 0.547 | 0.86 | 1.055 |
| tray spacing (mm) | 3.8 | 3.8 | 4 | 4 | 3.8 | 3.8 | 0.547 | 3.8 | 3.8 |
| diameter( m) | 0.0076 | 0.0076 | 0.008 | 0.008 | 0.0076 | 0.0076 | 0.0076 | 0.0076 | 0.0076 |
| sectional area(m²) | 0.000494 | 0.000787 | 0.00072 | 0.00072 | 0.00106 | 0.00106 | 0.00166 | 0.00225 | 0.00225 |
| angle diameter (mm) | 38 | 60 | 45 | 70 | 75 | 80 | 135 | 200 | 200 |
| capacity (m3/h) | 25 | 60 | 35 | 85 | 90 | 110 | 310 | 680 | 680 |
| heat exchange area( m²) | 1-5 | 3-10 | 3-10 | 4-25 | 5-30 | 8-40 | 25-120 | 50-180 | 80-250 |
| pressure (mpa) | 2.0 | 2.0 | 2.0 | 1.6 | 1.6 | 1.6 | 1.0 | 1.0 | 1.0 |
| working temperature | Depending on the gasket material |
Contact us immediately to get latest specification and price of PHE0.1B Plate Heat Exchanger Auxiliary Brewing Equipments 3-10m²
Heat Exchange Area
